HT-2000P V2:
Hipot Tester, 0-2000Vac @ 20mA

  • $1,420.00

The HT-P V2 series Hipot Testers emerges from the redesigned HT-P series, offering new long life buttons, robust design, lighter and cleaner appearance. Performs the Ground Continuity Test with a fix Pass/Fail point of 2.93Ω, 0-2000V AC Hipot Test, Neutral/Hot to Ground Leakage current test up to 20mA DC. Easy to use and connect. Ships complete with cables, manual, Calibration Certificate and Calibration Data Log Copy. Made in the USA. Calibration and repair services available. Not sure - contact us!

Available Options

Reviews (0)

Write a Review

Note: HTML is not translated!
    Bad           Good


  • High precision leakage current, duration and ground continuity settings.
  • Allows no load setup of leakage current and test dwell times.
  • Once entered, ground continuity setting, leakage current and test dwell times can be referenced on the front panel display when unit is not testing.
  • Leakage currents can be set from 1-20 mA AC in 0.1mA increments.
  • Dwell times can be set from 1-60 seconds in 1 second increments.
  • Two tests with one setup. Conducts UL/CSA Ground continuity and Hipot tests with one setup, so no additional equipment is needed.
  • Small and light. 9.25" wide x 4.75" high x 10" deep. 11 lbs. But rugged enough to test manufactured housing.
  • Ground continuity check is defeatable for testing two-wire products.
  • Easy equipment connections. Plug your equipment right into the NEMA plug on the front panel. No adapters needed!
  • J2 and J3 cords allow connection of pigtail power leads.
  • Simple test outcome judgement. Green lights mean pass - red lights mean fail. Failing tests sound a buzzer as well.
  • Ready for your UL Inspector out of the box. NIST Traceable Calibration Certificate to MIL-STD45662-A is included. Cal cert is in accordance with UL guidance.
  • Operation Instructions are printed on the rear panel for easy reference.
  • In-depth testing. Both true Arc Detection and Leakage Current circuits test the product to find problems.
  • RED lights and a buzzer leave no question if a failure has occurred.
  • Expandable for TUV/European Agency Testing. Can be connected to our GF-30ac 25A Ground Bond Tester with optional TEST-LINK™.
  • Easy shift-by-shift Function Test. Compatible with our Patented function checker HTT-1.


Voltage Test TypeAC
Voltage Range0-2000 AC
Leakage Current Set Point1-20 mA AC
Input Voltage Requirements117-127 V, 50 /60 Hz
Fuse Requirements1A, 120V Slow Blow
Arc DetectIndependent High Frequency Circuit
Leakage DetectIndependent Low Frequency Circuit
Ground Continuity Pass/Fail Point 2.93Ω, Defeatable
Test Time Range 1 - 60 Seconds
Ramp Time Range 1 - 5 Seconds
Voltage Meter Accuracy± 2 %
HV Shutdown by Ground Fail< 7 mS
Duty Cycle100%
Discharge Time< 1.3 Sec VDC at open circuit
Transformer Power< 500 VA
Pass/Fail Repeatability ± 3 %
Display 4 digits LED display
Test Indicator LED
Test Failure IndicatorLED and Buzzer
Relay Interface (PLC Interface) Optional
TestLink (With GF-30AC) Optional
Autoreset on PassOptional
Voltage Hold on failure No
Computer Control No
Programable No
Output Connector NEMA plug
Power Cord Included
Return Test Lead Included
J2 Test Lead Optional
J3 Test Lead Optional
Handle Kit Optional
Calibration Certificate Included
Calibration Cycle 1 year
Operation Temperature15 - 40 °C
Relative Humidity Range 0 - 90 % Non-condensing
Dimensions9.25" wide x 475" high x 10" deep
Weight11 Lbs


Download Manual
HT/HT-PV2 series Manual rev 1.0.pdf Download Manual
HT/HT-S and HT-P V2 Standard Relay Interface Connection rev 4.pdf Download Manual
HT/Hipot Testers Specs - Comparative Table.pdf Download Manual

Contact Us

Corporate Sales Office (USA)

Compliance West USA
650 Gateway Center Way Suite D
San Diego, CA 92102 USA

US Representatives

Product Update Bulletin

Newest Product: HT-3500S RF, "ruggedized" hipot tester

The HT-3500S RF tester is specifically designed for the challenges common to operating in the field. Along with heavy duty internal brackets and a sturdy, shock-absorbing case, this unit includes adjustable voltage output, voltage ramp, test time, leakage current and ground continuity limit settings - all controlled from an easy-to-access front panel. Call for pricing.

Read More

Available: 16A option for CDT-240

Perform one of the most difficult tests required with both speed and accuracy. The CDT-240 now offers a 16A option along with designed presets to implement the plug discharge test as described in IEC 61010, 60065 and 60335.

Read More

MegaPulse Defib 5P reaches EOL - Replaced by D5-PF

Compliance West USA is announcing the EOL (End-of-LIfe) of our MegaPulse Defib 5P series effective 07/14/2015. This unit has been replaced by our MegaPulse D5-PF advanced tester. Compliance West will continue to support, repair and calibrate the Defib 5P throughout the terms of any existing warranty agreements or up until the product's End-of-Support date. Please contact us with any questions.

Read More