Questions? Contact Sales: 800-748-6224
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 15A option for testing large equipment.
Questions? Contact us.
CDT 240 V2 Calibration Procedure Section 9.1
CDT-240: Conducting a Voltage Decay Test-Video
CDT-240: Conducting a Time Delay Test-Video
CDT-240: EN60950 Capacitive DIscharge Test-Video
CDT-240 Tolerance compared to oscilloscopes and CTL DSH 251e
T=0 Voltage Determination for CDT-240 using CBX (see Section 7)
T=0 Voltage Determination for CDT-240 CE Version (Internal Time constants) (See Section 8)
Recall Release Note (Not for V2, only previous version)
| TESTING CIRCUITRY | |
| Min/Max Test Voltage | 90/264 Vrms |
| Max Test Current | 8A, 15A option available |
| Fuse | 10A, 250V, time delay, 1-1/4" x 1/4" |
| Probe Impedance | > 100 Mohm, < 25pF |
| AC Peak Detection Accuracy | EUT disconnect within 5% of supply voltage peak |
| Test Time Range | 0.5 - 10.0 Seconds |
| Voltage Setting Range | +/-30 to 388V |
| Voltage Setting Resolution | 1V |
| Test Time Accuracy | +/-5% |
| Voltage Meter Accuracy | +/-2% of reading +/-0.8V |
| Frequency | 50-60Hz |
| ELECTRICAL | |
| Rated Input Voltage | 110-240 V |
| Frequency | 50/60 Hz |
| Fuse | 2A, 250V, time delay, 5x20 mm |
| ENVIRONMENTAL | |
| Operation Temperature | 15 - 40 C |
| Relative Humidity Range | 0 - 90 % Non-Condensing |
| SAFETY | |
| (XI) Safety Interlock | 2 pin terminal block on rear panel, shorted for tester operation |
| GENERAL | |
| Dimms | 9-1/4"W x 4-3/4"H x 10"D |
| Wt | 5.8lbs |
| BNC Output | Referenced to ground, 100:1 of measured voltage |
| Download Manual | |
| CDT-240 V2/CDT-240 (CE) rev 2.pdf | Download Manual |
Compliance West USA
650 Gateway Center Way Suite D
San Diego, CA 92102 USA
The HT-3500S RF tester is specifically designed for the challenges common to operating in the field. Along with heavy duty internal brackets and a sturdy, shock-absorbing case, this unit includes adjustable voltage output, voltage ramp, test time, leakage current and ground continuity limit settings - all controlled from an easy-to-access front panel. Call for pricing.
Perform one of the most difficult tests required with both speed and accuracy. The CDT-240 now offers a 16A option along with designed presets to implement the plug discharge test as described in IEC 61010, 60065 and 60335.
Compliance West USA is announcing the EOL (End-of-LIfe) of our MegaPulse Defib 5P series effective 07/14/2015. This unit has been replaced by our MegaPulse D5-PF advanced tester. Compliance West will continue to support, repair and calibrate the Defib 5P throughout the terms of any existing warranty agreements or up until the product's End-of-Support date. Please contact us with any questions.