Capacitor Discharge Tester, 8A

  • Capacitor Discharge Tester, 8A
  • Product Views
Datasheet

CDT-240 8A:
Capacitor Discharge Tester, 8A

  • $2,695.00

For IEC Testing of residual voltage after plug disconnect.  The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results.  Scope output for viewing decay waveform.  Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335.  Recommendations for Pluggable Type B equipment.  NIST calibration supplied; A2LA calibration available.  15A option for testing large equipment.

Questions?  Contact us.

EN60950 Video

CBX R-C Time Constant Video

More information

CDT-240 Tolerance compared to oscilloscopes and CTL DSH 251e


Recall Release Note


Available Options

Reviews (0)

Write a Review

Note: HTML is not translated!
    Bad           Good

Features

  • Accurate; in accordance with CTL voltage and time specifications.
  • Disconnects input test voltage at positive or negative peak, normal and reversed polarity
  • Tests Line-Ground, Line-Neutral and Neutral-Ground.
  • Micro-controller Technology, one button test, easy setup, LCD display indicates test results.
  • Maximum Rated Test Current 8A, 15A optional.
  • Ergonomically designed for safety, speed and efficiency.
  • Designed for product development, production and laboratory use.
  • Rugged construction that can withstand a 6" drop with no damage.
  • Cables, manual and calibration certificate included.
  • One year warranty.

Specifications

TESTING CIRCUITRY
Min/Max Test Voltage90/264 Vrms
Max Test Current8A, 15A option available
Fuse10A, 250V, time delay, 1-1/4" x 1/4"
Probe Impedance> 100 Mohm, < 25pF
AC Peak Detection AccuracyEUT disconnect within 5% of supply voltage peak
Test Time Range0.5 - 10.0 Seconds
Voltage Setting Range+/-30 to 388V
Voltage Setting Resolution1V
Test Time Accuracy+/-5%
Voltage Meter Accuracy+/-2% of reading +/-0.8V
Frequency50-60Hz
ELECTRICAL
Rated Input Voltage110-240 V
Frequency50/60 Hz
Fuse2A, 250V, time delay, 5x20 mm
ENVIRONMENTAL
Operation Temperature15 - 40 C
Relative Humidity Range0 - 90 % Non-Condensing
SAFETY
(XI) Safety Interlock2 pin terminal block on rear panel, shorted for tester operation
GENERAL
Dimms9-1/4"W x 4-3/4"H x 10"D
Wt5.8lbs
BNC OutputReferenced to ground, 100:1 of measured voltage

Manuals

Contact Us

Corporate Sales Office (USA)

Compliance West USA
650 Gateway Center Way Suite D
San Diego, CA 92102 USA

US Representatives

Product Update Bulletin

Newest Product: HT-3500S RF, "ruggedized" hipot tester

The HT-3500S RF tester is specifically designed for the challenges common to operating in the field. Along with heavy duty internal brackets and a sturdy, shock-absorbing case, this unit includes adjustable voltage output, voltage ramp, test time, leakage current and ground continuity limit settings - all controlled from an easy-to-access front panel. Call for pricing.

Read More

Available: 16A option for CDT-240

Perform one of the most difficult tests required with both speed and accuracy. The CDT-240 now offers a 16A option along with designed presets to implement the plug discharge test as described in IEC 61010, 60065 and 60335.

Read More

MegaPulse Defib 5P reaches EOL - Replaced by D5-PF

Compliance West USA is announcing the EOL (End-of-LIfe) of our MegaPulse Defib 5P series effective 07/14/2015. This unit has been replaced by our MegaPulse D5-PF advanced tester. Compliance West will continue to support, repair and calibrate the Defib 5P throughout the terms of any existing warranty agreements or up until the product's End-of-Support date. Please contact us with any questions.

Read More