A great product that won't break the bank. It's easy to use and easy on the bottom line. Adds precision leakage current and test time setup and viewing to the popular HT-2000.

Ships complete with cables, a manual, and a Calibration Certificate. Made in the USA.

Calibration and Repair services available

Video: Using a Compliance West Hipot/Ground Continuity Tester
Video: Setting Test Time and Leakage Current Limits with a HT-2000P
Video: Hipot Testing for Products without a Power Cord
Video: TestLink: Connection and Setup

    TOP

HT-2000P AC Hipot Tester

Voltage Test Type	AC
Voltage Range	0-2000 V
Current Range	1-20 mA
Input Voltage Requirements	117-127 V, 50 /60 Hz
Fuse Requirements	120 V, 1.5 A
Arc Detect	Separate high Frequency  circuit
Leakage Detect	Separate Low frequency circuit
Ground Continuity	3 ohm (Defeatable)
Ground Continuity Current	47 mA
Test Time Range	1 - 60 seconds
Ramp time Range	1 - 5 Seconds
Voltage Meter Accuracy	± 5 %
HV shutdown by Ground Fail	<  7 mS
Duty cycle	100%
Discharge Time	< 100 mS
Transformer Output	< 500 VAC
Pass/Fail Repeatability	± 3 %
Output connector	NEMA plug
Display	4 digits LED display
Test indicator	Led indicators
Failure Indicator	Led indicators and buzzer
Programable	No
PLC Interface	Optional
TestLink	Optional
Testminder	No
Top Mounted handle	Optional
Test Defeat	Ground continuity
Autoreset on Pass	Optional
Operation Temperature	15 - 40 °C
Relative Humidity Range	0 - 90 % Non-condensing
Dimensions	9-1/4" wide x 4-3/4" high x 10" deep
Weight	14 Lbs
Calibration	One year calibration Certificate
Test Cords	Retuurn Lead, Power Cord J2 and J3 Optional

    TOP

Option J2 and J3: Jumpers for testing products without plugs
Option TL: TEST-LINK™ upgrade
Option HAN: Carrying Handle
Option AR: Auto Reset on Pass
Option RI: PLC Interface Board
Option HO: Front Panel High Voltage Receptacle
Option HVP: HV Probe
Option HTT-1: HTT-1 Hipot and Ground Continuity Function Checker

    TOP

• Adds high precision leakage current and duration settings to the user-friendly HT-2000 for better control of tests.
• Allows no load setup of leakage current and test dwell times.
• Once entered, leakage current and test dwell times can be referenced on the front panel display at any time.
• Leakage currents can be set from 1-20mA in 0.1mA increments.
• Dwell times can be set from 1-60 seconds in 1 second increments.
• Two tests with one setup. Conducts UL/CSA Ground continuity and Hipot tests with one setup, so no additional equipment is needed.
• Small and light. 9.25" wide x 4.25" high x 10" deep. 11 lbs. But rugged enough to test manufactured housing.
• Ground continuity check is defeatable for testing two-wire products.
• Easy equipment connections. Plug your equipment right into the NEMA plug on the front panel. No adapters needed!
• J2 and J3 cords allow connection of pigtail power leads.
• Simple test outcome judgement. Green lights mean pass - red lights mean fail. Failing tests sound a buzzer as well.
• Ready for your UL Inspector out of the box. NIST Traceable Calibration Certificate to MIL-STD45662-A is included. Cal cert is in accordance with UL guidance.
• Operation Instructions are printed on the rear panel for easy reference.
• In-depth testing. Both true Arc Dectection and Leakage Current circuits test the product to find problems.
  RED lights and a buzzer leave no question if a failure has occurred.
• Expandable for TUV/European Agency Testing. Can be connected to our GF-30ac 25A Ground Bond Tester with optional TEST-LINK™.
• Optional 120kohm calibration resistor can be mounted on the rear panel.
• Easy shift-by-shift Function Test. Compatible with our Patented function checker, the HTT-1.

    TOP