Surge Tester 1.2x50/8x20-12P 2 ohm, Grounded output (No CDN)

  • Surge Tester 1.2x50/8x20-12P 2 ohm, Grounded output (No CDN)
  • Product Views
Datasheet

MegaPulse 1.2x50/8x20-12±2 ohm:
Surge Tester 1.2x50/8x20-12P 2 ohm, Grounded output (No CDN)

  • $12,000.00

The MegaPulse 1.2x50-12±2 ohm is our 12kV, 6kA combination tester, with a 30 second cycle time. It can produce a combination test waveform at 2 ohms from 500V to 12kV, in tolerance with EN 60060.

For example, the MegaPulse 1.2x50/8x20-12±2 ohm Surge Tester is specifically designed to perform the Impulse Test on transient overvoltage limiting devices in accordance with EN 61010, Para. 14.9, Table 17 and Table 18. This tester can perform all the tests shown in Table 17 at either 2 or 12 ohms as shown in Table 18. The output is in accordance with the published waveform from 500-12000V peak (open and short circuit). The tests can be done with a 30 second or longer wait between pulses, well within the Standard requirement of 1 minute or less. A 12 ohm tap is provided for testing Category II devices in accordance with Table 18, in accordance with the Standard. The 12 ohm tap will be in accordance with the tolerances of the voltage waveform only, as allowed by the Standard.

The MegaPulse 1.2x50/8x20-12±2 ohm is equipped with a relay allowing switch selected polarity output. With the switch selected polarity output, users may opt for computer control via our option TestMinder MegaPulse, or PLC guided operation with our Relay Isolated Control board. Some users may not need this level of automation in their testing, and we can accomodate them with our model MegaPulse 1.2x50/8x20-12+2 ohm. Polarity is changed by manually switching leads.

The tester charges in less than 30 seconds. Sold with a one year warranty and calibrated to NIST Standards. A2LA Cal available at extra charge.

Pos/neg polarity, grounded output, 500V min, 12 ohm tap; not for use with CDN. 30 sec duty cycle, <30 sec. charge time.

Available Options

Reviews (0)

Write a Review

Note: HTML is not translated!
    Bad           Good

Features

  • Outputs a combination waveform at 500 - 12kV, 2 ohms.
  • Front panel switch allows waveform reversal (±2 ohm model only).
  • 30 second pulse repeat rate.
  • 12 ohm tap provided, in accordance with EN60060 (voltage waveform only).
  • Can be controlled from PLC or LabView with Option RI (±2 ohm model only).
  • Outputs up to 12000V peak.
  • Virtual Impedance of 2/12 ohms.
  • Available TestMinder for computer control of long test sequences (±2 ohm model only).
  • Provided with NIST calibration good for one year; A2LA/17025 calibration available.
  • 1 year warranty.

Specifications

See Datasheet Link above for Specifications.
See Datasheet Link above for Specifications.

Manuals

Download Manual
MegaPulse 1.2x50 8x20-12P 2ohm 12ohm rev 1.0.pdf Download Manual
Download Manual
Waveforms/1.2x50-8x20-12 2-12 waveforms.pdf Download Manual

Contact Us

Corporate Sales Office (USA)

Compliance West USA
650 Gateway Center Way Suite D
San Diego, CA 92102 USA

US Representatives

Product Update Bulletin

Newest Product: HT-3500S RF, "ruggedized" hipot tester

The HT-3500S RF tester is specifically designed for the challenges common to operating in the field. Along with heavy duty internal brackets and a sturdy, shock-absorbing case, this unit includes adjustable voltage output, voltage ramp, test time, leakage current and ground continuity limit settings - all controlled from an easy-to-access front panel. Call for pricing.

Read More

Available: 16A option for CDT-240

Perform one of the most difficult tests required with both speed and accuracy. The CDT-240 now offers a 16A option along with designed presets to implement the plug discharge test as described in IEC 61010, 60065 and 60335.

Read More

MegaPulse Defib 5P reaches EOL - Replaced by D5-PF

Compliance West USA is announcing the EOL (End-of-LIfe) of our MegaPulse Defib 5P series effective 07/14/2015. This unit has been replaced by our MegaPulse D5-PF advanced tester. Compliance West will continue to support, repair and calibrate the Defib 5P throughout the terms of any existing warranty agreements or up until the product's End-of-Support date. Please contact us with any questions.

Read More